User:Remi Scarlet/Blog/FurutakaKaiNiCosplay/Day7

Day 7

Date: 5/29/15
Time spent: ~4 hours

Show/Hide Day 7

So after trying to avoid the problem for a few days, I finally gave in and decided to work on the roofing and walls for the shoulder cannon. Basically the reason I didn't want to start on this so much was because I felt like measuring out and cutting the front wall where the cannon barrels stick out would be annoying since... well, I'll just show a pic.

Basically getting the cut from the corner of the top to the corner of the bottom and making sure the cannon barrel has space to move

Something I should also note here that the top piece was inserted after cutting away about 0.25inches of the top from the horizontal support grid. You can see it in the following picture, but the tip of the slope actually covers the thickness of the top foam board. Those words probably made zero sense so just look at the image.

Notice how the cut was made so the thickness of the top piece is embedded in.

That done, I had to actually start cutting out test cuts from non-prepared paper to make sure my measurements and whatnot were correct. Remember from day 1 that I had prepared a few sheets of "layered" paper so as to act as a sturdier and more versatile "sheet". As a note, I've been making about 4 of these every other day or so, even though I haven't been denoting as such on the blog.

Thin piece of paper cut out to act as a model. How many times have you seen paper pinned with clothes pins? lol

Measuring out the exact dimensions can be a bit difficult for stranger cuts and locations such as the diagonal corners of the cannon's front, as denoted earlier. As such, I basically did some measurements and trig to get the supposed lengths and sizes for the corners and hoped for the best. A clever trick I used here is that for the triangular flap that's at the end of the half trapezoid, I knew the triangular cut had to have a 1inch leg and a 2.75inch leg so I made a circle with 1inch radius and used a ruler to connect the third leg's endpoint to the point on the curve that made it exactly 2.75inches. As it turns out, which should have been obvious if I had thought about it a bit, that it's just the tangent line to the curve. This part also probably made zero fucking sense so just look at the image. That done, I now had to simply cut out the slice with my X-acto knife.

Measuring out the dimensions of the side mount with a test piece of paper (Not using the prepared layered sheets).

• 

  Cutting out the paper. And my gf's boba plush.

• 

  Test aligning the example cutout

• 

  Fitting

That all said and done, I decided my cut was mostly good and just needed a few small adjustments. One of these adjustments was that the triangular flap that went on the front side of the cannon needed to be adjusted a little bit. I accounted for these in my following "final" diagram that I proceeded to cut out and prepare.

• 

  Measuring out again on the layered paper

• 

  Likewise for the other side (left and right halves)

• 

  Diagram cut out. Since the paper is layered, you can very lightly cut along the lines with the X-acto knife to cut the "first layer" of the paper so it folds easier like this.

• 

  Another shot of the cutout

That done, I simply pasted it on and I ended up with a little something like this.

Not too shabby looking, I'd say.

The rest of the progress done are pretty self-explanatory so I'll just do another gallery style dump here. The remaining images are basically showing the shell-like layering I'm doing for the rest of the body of the cannon and some final shots of the shell covering it except for the final piece which will be visibly missing.

• 

  Measurements for the layers along the top of the cannon.

• 

  Mostly finished. Just need to put on last layer at the very back.

• 

  Shot of the cannon's front.

• 

  From above.

• 

  Distanced and cannons aimed up

• 

  Close-up of the front

My name is Remi. If you make me angry, I will send out a litle boy named Peter Pan to kick your ass and I like dipping chairs in chicken blood. Props are so tanoshii. I have sinned and poked boba-kun in the eye but he loves me now. I like to walk my pet chimera everyday and sing songs with my imaginary friend Sagua. My favorite ship class is the carrier because they hold all the brand new suzukis and launch flying cars across the ocean.